Note: I found these instructions a little outdated for the current Sid. the ["DistroAndHardwareSetup/Ubuntu_Breezy_Badger"] worked well for me as of early 2006.
Note2: The instructions work again (April 02006) for sid - just use the first downloadable initrd-script. YMMV.
- --LarsK
Note3: Prepackaged debian kernels up from 2.6.17 use yaird to configure initrd, for more information see on the bottom of this page
Incorporating modular Software Suspend support into the 2.6 Debian kernels is relatively easy (2.4 modular Software Suspend was not available at time of writing). Note - unless you require Software Suspend to be built as modules, it is much less painful to build them directly into the kernel (making this page largely irrelevant). If you wish to proceed anyway, here goes...
Steps:
- Apply the patches for Software Suspend 2.0.0.103 or later against your favourite 2.6 kernel.
Use make-kpkg with the --initrd option to create a kernel image package.
- Ensure you have installed the initrd-tools package.
- Drop the below script into /etc/mkinitrd/scripts/.
- Install your kernel with dpkg.
eg:
/usr/src$ tar xjf kernel-source-2.6.10.tar.bz2 /usr/src$ cd kernel-source-2.6.10 /usr/src/kernel-source-2.6.10$ /tmp/software-suspend-2.1.7-for-2.6.10/apply
Check everything applies cleanly (it should).
/usr/src/kernel-source-2.6.10$ cp /boot/config-`uname -r` .config /usr/src/kernel-source-2.6.10$ make menuconfig
Select Power Management Options -> Software Suspend 2. Select Modules (press M) for "Software Suspend 2", "Swap Writer", "LZF image compression", and "Text mode console support" (bootsplash if you so desire - but you will need to modify the script below to load that module too).
/usr/src/kernel-source-2.6.10$ make-kpkg --revision swsusp.1 --rootcmd fakeroot --initrd kernel-image [... kernel builds ...] /usr/src/kernel-source-2.6.10$ cd .. /usr/src$ dpkg -i kernel-image-2.6.10_swsusp.1_i386.deb [... package installs ...]
Initrd script
[attachment:swsusp-initrd-text-for-all-versions-plain.txt Click to download the script]
[attachment:swsusp-initrd-text-plain.txt Click to download the older script (not working for 2.2-rc8 and newer)]
[attachment:swsusp-initrd-text.txt Click to download the old script with module support - not needed for recent Suspend2 versions]
Make sure this script is called /etc/mkinitrd/scripts/swsusp2 (no special characters like a dot ...) and is executable. It only works with swap partitions, not swap files. For swapfiles, you will need to set the resume2= parameter in GRUB/LILO manually. Also note that if you are using swap partitions, this script alleviates the need to specify a resume2= parameter on the kernel command line.
If you are using a version prior to 2.1.2, then you will need to change do_resume in the script to activate.
Didn't work for me (on kernel 2.6.12). I found a script that works here: http://www.mm.bme.hu/~szazs/IBMtpT42.html
cat <<EOF >>$INITRDDIR/script
if [ -z "\$noresume" ]; then # be careful with the 'dollar' sign
echo >/proc/software_suspend/do_resume
# IMPORTANT: use the line below for version 2.2-rc8 and newer
# echo >/proc/suspend2/do_resume
umount -n devfs
umount -n proc
fi
EOFNeither the script from suspend2.net nor the script above worked for me so I took following way:
$ mkinitrd -k -o /boot/initrd.img-2.6.14.3 2.6.14.3 $ cd /tmp/mkinitrd.* $ echo "echo > /proc/suspend2/do_resume" >> initrd/linuxrc $ mkcramfs initrd/ /boot/initrd.img-2.6.14.3
Ok, this last one works for me, BUT I had to create the swap device inside initrd image. Using the steps above, do it before the mkcramfs command:
$ cd initrd/dev $ mknod hda b 3 0 $ mknod hda1 b 3 1
where hda1 is your swap partition or the partition where you will save the resume image. Change it if you are using another partition. 18-01-2006 -- TiagoVaz
Getting yaird to work
I have yaird 0.0.12 here YMMV. Edit the file /etc/yaird/Default.cfg, after the first line that loads modules, here is my diff:
MODULE mousedev
MODULE evdev
+ MODULE sata_nv
+ MODULE sd_mod
+ MODULE scsi_mod
+ MODULE libata
+
+ TEMPLATE resume
#
# NETWORK -- Insert modules for all ethernet devicesPlease note that loading all those modules is necessary only for SATA disks. My swap partition is /dev/sda1 (on sda harddrive), so I need to load those modules, otherwise Supsend2 will not be able to see the swap partition. If you have a swap partition on ATA drive, then you can skip loading those modules.
Next, you have to edit the file /etc/yaird/Templates.cfg, here is my diff:
2.6.17:
END TEMPLATE
+ TEMPLATE resume
+ BEGIN
+ SCRIPT "/init"
+ BEGIN
+ !if [ -z "$noresume" ]
+ !then
+ ! echo swap:0801 > /proc/suspend2/resume2
+ ! echo > /proc/suspend2/do_resume
+ !fi
+ END SCRIPT
+ END TEMPLATE
TEMPLATE insmod2.6.18 is a little different:
+ ! echo swap:0801 > /sys/power/suspend2/resume2 + ! echo > /sys/power/suspend2/do_resume
You can add this code anywhere between templates. I have added it before TEMPLATE insmod, but it's not important. It is very important to write a correct name for swap device in my case it was:
swap:0801
That is magic name for /dev/sda1 - yaird cannot access /dev filesystem so we have to access /dev/sda1 by using this magic number, and this number will change from kernel to kernel! So you have to determine it with following command:
echo `perl -e "@a=stat '/dev/sda1';printf 'swap:%04x', \\$a[6]"`
But remember to replace /dev/sda1 with your swap device. Then you can put this magic number into /etc/yaird/Templates.cfg with the diff presented above.
After those changes are done a simple reinstall of linux-image will apply your modifications:
sudo dpkg -i ./linux-image-2.6.17-2-k7_2.6.17-6_i386.deb
Now you can hibernate and it will work. There is no need to modify grub's menu.lst file. Yaird takes care of that by calling suspend2 when needed.